Hot Products
0102030405
China Snap-In Vent Plug - ZZPIP-Vent Plug_D17_E20WO from Leading Suppliers and Factory
Product Technical Data Sheet
| PRODUCT NAME | Snap-In Vent Plug |
| PRODUCT MODEL | ZZPIP-Vent Plug_D17_E20WO |
| PRODUCT DIAGRAM |
|
| MEMBRANE MODEL | ZZPIP-E20WO |
| APPLICATION FIELD | Chemicals Packaging |
| APPLICATION CHEMICAL | Bleacher, Disinfectant, Amino Acid, Agrochemicals, Liquid Fertilizer |
Product Properties
| PHYSICAL PROPERTIES | REFERED TEST STANDARD | UNIT | TYPICAL DATA |
|---|---|---|---|
| Plug Material | / | / | HDPE |
| Plug Color | / | / | White |
| Membrane Construction | / | / | PTFE/PO non-woven |
| Membrane Surface Property | / | / | Oleophobic & Hydrophobic |
| Typical Air Flow Rate | ASTM D737 (Test Area: 1cm²) | ml/min @ 7KPa | 1200 |
| Water Entry Pressure | ASTM D751 (Test Area: 1cm²) | KPa dwell 30 sec | ≥70 |
| IP Grade | IEC 60529 | / | IP67/IP68 |
| Moisture Vapor Transmission | ASTM E96 | g/m²/24h | >5000 |
| Oleophobic Grade | AATCC 118 | Grade | ≥7 |
| Service Temperature | IEC 60068-2-14 | ℃ | -40℃ ~ 125℃ |
| ROHS | IEC 62321 | / | Meet ROHS Requirements |
| PFOA & PFOS | US EPA 3550C & US EPA 8321B | / | PFOA & PFOS Free |
Application
This series of vent plug could equalize the pressure differentials of chemical containers which caused by temperature difference, altitude changes and releasing/consuming gases, in order to prevent container deformation and liquid leakage.
The vent plugs can be used in breathable cap products for chemicals packaging containers, and be suitable for High-concentration Hazardous Chemicals, Low-concentration Household Chemicals, Agricultural Chemicals and other Special Chemicals.
The vent plugs can be used in breathable cap products for chemicals packaging containers, and be suitable for High-concentration Hazardous Chemicals, Low-concentration Household Chemicals, Agricultural Chemicals and other Special Chemicals.
Shelf Life
Shelf life is two years from the date of receipt for this product as long as this product is stored in its original packaging in an environment below 80° F (27° C) and 60% RH.
Technical Notes & Disclaimer
All data above are typical data for the membrane raw material, for reference only, and should not be used as special data for outgoing quality control. All technical information and advice given here is based on ZZPIP previous experiences and test results. ZZPIP gives this information to the best of its knowledge, but assumes no legal responsibility. Customers are asked to check the suitability and usability in the specific application, since the performance of the product can only be judged when all necessary operating data are available.
Frequently Asked Questions
What is the primary function of the Snap-In Vent Plug?
The Snap-In Vent Plug is designed to equalize pressure differentials in chemical containers. These pressure changes are typically caused by temperature variations, altitude shifts, and the releasing or consuming of gases. By equalizing pressure, the plug prevents container deformation and liquid leakage.
What types of chemicals is this vent plug compatible with?
It is suitable for a wide range of chemical packaging applications, including high-concentration hazardous chemicals, low-concentration household chemicals, agricultural chemicals (like liquid fertilizers), disinfectants, amino acids, and bleachers.
What are the material specifications of the plug and membrane?
The plug body is constructed from HDPE (High-Density Polyethylene) in white. The membrane is made of a PTFE/PO non-woven material featuring both oleophobic and hydrophobic surface properties (Oleophobic Grade ≥7).
What are the environmental standard compliances for this product?
This vent plug meets ROHS requirements (tested under IEC 62321) and is completely PFOA & PFOS free (tested under US EPA 3550C & US EPA 8321B).
What is the storage life and condition for the Snap-In Vent Plug?
The product has a shelf life of two years from the date of receipt, provided it is stored in its original packaging in a controlled environment below 80°F (27°C) and with a relative humidity (RH) of 60% or less.